 |
|
| Hello, you are currently browsing to Retro-Renault Archive which is a copy of our old forum. You cannot post replies in this forum. Please click here to go to the active website.
|
| Author |
Message |
drifter 340
Newbie
Joined: 03 Jul 2006
Posts: 3
|
| Posted:
Mon Jul 03, 2006 1:10 pm |
|
hello all i hope you can help me im trying to remove the loom from my 19 16v and am going to fit in to another car can anybody tell me which wires i need to cut to patch in to my other car? and where they are? or if they know of anyone who can do this job for me?
many thanks
lee |
|
|
|
|
Neal
Forum Moderator
Joined: 18 Feb 2004
Posts: 7432
|
| Posted:
Mon Jul 03, 2006 1:13 pm |
|
why do you need to cut any wires?
Just unplug all the plugs and remove the loom  |
|
|
|
|
drifter 340
Newbie
Joined: 03 Jul 2006
Posts: 3
|
| Posted:
Mon Jul 03, 2006 1:18 pm |
|
yes but what wires do i need to use off the plugs to run the engine in another car?
thanks
lee |
|
|
|
|
Chris H
Forum Moderator
Joined: 02 Mar 2004
Posts: 19978
|
| Posted:
Mon Jul 03, 2006 3:47 pm |
|
the 3rd one on the right.
A bit more info would help you know. |
|
|
|
|
Chet T16
Retroholic
Joined: 12 Feb 2004
Posts: 5685
|
| Posted:
Tue Jul 04, 2006 3:04 am |
|
| Chris H";p="99945 wrote: |
| the 3rd one on the right. |
Round the outside, round the outside. |
|
|
|
|
drifter 340
Newbie
Joined: 03 Jul 2006
Posts: 3
|
| Posted:
Tue Jul 04, 2006 10:11 am |
|
what other info do you need? i have seen the conversions to the reno 5 so what wires do i need from the loom plugs and what do i connect them to?
the engine is going in to a volvo 340.
thanks
lee |
|
|
|
|
Chet T16
Retroholic
Joined: 12 Feb 2004
Posts: 5685
|
| Posted:
Tue Jul 04, 2006 12:33 pm |
|
Excellent plan 
You'll need to spread the loom out across the floor and get yourself an ECU pin-out and take it from there
I had started to do similar for my project
| Chet T16";p="89511 wrote: |
Still not much progress made, my head isn't finished yet and i'm waiting for my sump to come back from being reinforced
Today i managed to spread my 19 16v loom across the floor and start removing the unneeded bits. As its a megane engine being used the actual engine control loom isn't needed, any part that goes between the ECU and a sensor was removed. For example the MAP sensor wiring was cut out .
Some wires are still attached to the ECU plug, this is either becuase they will need matching up to the emerald or are needed for something else.
I have to say some of the renault wiring really baffles me!
This pic shows a work in progress, there is still more to remove but until i can get my wiring diagram i'm a bit stuck!
[img:960:1280:311590c07a]http://www.renault-turbo.com/710/19loom.jpg[/img:311590c07a] |
|
|
|
|
|
|
|
| |