 |
 |
|
Welcome to the Retro-Renault forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features including the tech articles. Registration is fast, simple and absolutely free so please, join Retro-Renault now! If you have any problems with the registration process or your account login, please contact us. PLEASE NOTE: If you were a member of Retro-Renault on the old site you will now need to re-register. |
|
|||||||
 |
|
|
LinkBack | Report Tools | Display Modes |
Published by Chet T16
8th October 2006 |
|||||||||||||||||||
|
|||||||||||||||||||
|
|||||||||||||||||||
|
By
Chet T16
on
11th November 2006, 04:21 PM
|
|
Updated 11/11/06
|
|
|
By
aerodynamic
on
24th December 2006, 11:29 AM
|
 I see that youre using a Rover mapsensor and wiring,But i could not understand why, Ive you get a R21T mapsensor which sees boost, En remap the orginal renix/siemenis you can use the orginal wiring. or get a Fastchip: Code:
Necessary for Turbocharging a F7P & F7R 16V engine. Features: Up to 1.1 Bar boost Adapted to BOSCH 0280 150 802 Injectors Altered closed loop Safety ignition retard due to higher intake temperatures Changed start and warm-up fuel delivery Optional Boost cut-off limiter Price EUR 275,- Its only an advise keep up the good work |
|
|
|
By
aerodynamic
on
24th December 2006, 05:53 PM
|
|
|
Quote:
But you have allready a turbo 19 running? |
|
|
|
|
By
aerodynamic
on
24th December 2006, 10:12 PM
|
|
|
Quote:
What was the lifetime of it? What about the driveablity? in the netherlands we talk about milibars not in psi. But 5psi is 350milibar and isnt much. My goal 800milibars and is 12psi with an compression ratio of 9 to 1. High compression ratio's with relative highboost prevent turbo lags. But ran closer to nocklevels. Good map work is the key for succes with a good intercooler. My cooling system is allmost orginal, i only changed thermostat to 82 degrees Celsius with a heatchanger under the oilfiltre it will be enough. |
|
|
|
|
By
Dave@AVT
on
24th December 2006, 11:25 PM
|
|
|
Quote:
|
|
|
|
|
By
Chet T16
on
24th December 2006, 11:26 PM
|
|
I guess about 190bhp but i never had it on a rolling road, thats just in comparison to other cars. With the T28 there was minimal lag and acceleration in 5th gear from 2.5k rpm was very impressive.
After about 6k miles the crank started to get a very slight rattle on startup and 4th and 5th gears had gotten a bit noisey. This was an engine with over 100k on it before turboing. Running on 95 octane fuel 5psi was the very limit with my setup, in higher gears more than a few seconds and WOT with result in pinking. A 25% AvGas mix made it run very very nice. I have no idea of intake temps but its something i'd like to monitor on the new engine. I had a low temp thermostat and fan switch in it and never had a single problem with temps, even without the coolant/oil heat exchanger |
|
|
|
By
Chet T16
on
24th December 2006, 11:28 PM
|
|
|
Quote:
Still awaiting a reply to my PM  |
|
|
|
|
By
aerodynamic
on
26th December 2006, 11:23 AM
|
|
|
|
By
aerodynamic
on
26th January 2007, 10:07 AM
|
|
Updates yet?
|
|
|
|
«
F7R 710 Engine Rebuild
|
-
»
| Report Tools | |
| Display Modes | |
Linear Mode
|
|
All times are GMT. The time now is 02:08 PM.
